Steps for USB cable using KPPP configuration
1) connect ur nokia mobile to system
2)Check ur nokia connection as it's vendor and product number
[root@server1 ~]# lsusb
Bus 001 Device 001: ID 0000:0000
Bus 002 Device 004: ID 0421:0061 Nokia Mobile Phones
Bus 002 Device 003: ID 0e0f:0002
Bus 002 Device 001: ID 0000:0000
3)Add ur modem here with following command
[root@server1 ~]# sudo /sbin/modprobe usbserial vendor=0x421 product=0x061
4)add ur setting with following command
[root@server1 ~]# wvdialconf /etc/wvdial.conf
Scanning your serial ports for a modem.
ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
ttyS1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Port Scan<*1>: S2 S3
WvModem<*1>: Cannot get information for serial port.
ttyACM0<*1>: ATQ0 V1 E1 -- OK
ttyACM0<*1>: ATQ0 V1 E1 Z -- OK
ttyACM0<*1>: ATQ0 V1 E1 S0=0 -- OK
ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttyACM0<*1>: Modem Identifier: ATI -- Nokia
ttyACM0<*1>: Speed 4800: AT -- OK
ttyACM0<*1>: Speed 9600: AT -- OK
ttyACM0<*1>: Speed 19200: AT -- OK
ttyACM0<*1>: Speed 38400: AT -- OK
ttyACM0<*1>: Speed 57600: AT -- OK
ttyACM0<*1>: Speed 115200: AT -- OK
ttyACM0<*1>: Speed 230400: AT -- OK
ttyACM0<*1>: Speed 460800: AT -- OK
ttyACM0<*1>: Max speed is 460800; that should be safe.
ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
WvModem<*1>: Cannot get information for serial port.
ttyUSB0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyUSB0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyUSB0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Found an USB modem on /dev/ttyACM0.
Modem configuration written to /etc/wvdial.conf.
ttyACM0
[root@server1 ~]#
[root@server1 ~]# vim /etc/wvdial.conf
[root@server1 ~]# wvdial
--> WvDial: Internet dialer version 1.54.0
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: AT+CGDCONT=1,"IP","aircelgprs","",0,0
AT+CGDCONT=1,"IP","aircelgprs","",0,0
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
--> Modem initialized.
--> Sending: ATDT*99#
--> Waiting for carrier.
ATDT*99#
CONNECT
~[7f]}#@!}!} } }2}#}$@#}!}$}%\}"}&} }*} } g}%~
--> Carrier detected. Starting PPP immediately.
--> Starting pppd at Sun Oct 4 03:25:12 2009
--> pid of pppd: 9507
--> Using interface ppp0
--> pppd: 60800
--> pppd: 60800
--> pppd: 60800
--> pppd: 60800
--> local IP address 10.183.117.164
--> pppd: 60800
--> remote IP address 10.6.6.6
--> pppd: 60800
--> primary DNS address 202.148.200.3
--> pppd: 60800
--> secondary DNS address 202.148.202.4
--> pppd: 60800
Caught signal #2! Attempting to exit gracefully...
--> Terminating on signal 15
--> pppd: 60800
--> Connect time 7.2 minutes.
--> pppd: 60800
--> pppd: 60800
--> pppd: 60800
--> Disconnecting at Sun Oct 4 03:32:23 2009
root@server1 proc]# cat /etc/wvdial.conf
[Dialer Defaults]
Modem = /dev/ttyACM0
Init1 = AT+CGDCONT=1,"IP","aircelgprs","",0,0
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Baud = 460800
#Init1 = ATZ
#Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ISDN = 0
Modem Type = USB Modem
; Phone =
; Username =
; Password =
Username = a
Password = a
Phone = *99#
Stupid Mode = 1
check the kppp pakage and start ur linux in graphic mode with startx
open kppp-->applications-->internet-->kppp
click on configure-->click account tab and click on new-->Manual setup-->dial-->connection name--aircel
clikc add--enter a phone no as put-->*99#--ok-->0k
click on Modems tab-->>New-->Modem name--/dev/ttyAMC0-->modem device-->select /dev/ttyAMC0
now click on Modem tab-->Modem commands-->
Initialization strings1=AT+CGDCONT=1,"IP","aircelgprs","",0,0
Initialization strings2=ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
click -ok
Query Modem to test it-
click ok and ok
put the user name=a
password = a
now connect ur aircel gprs properly
HOWTO: Airtel GPRS on Linux via Bluetooth
Here’s a mini HOWTO explaining how Airtel GPRS users can connect their linux boxes to the net using only a bluetooth connection from their phone. That’s right, no data cable required!
NOTE: I’ve only tried this on Debian but it should work fine on just about any distro.. use your distro’s package management tool instead of apt.
Follow these steps:
1. First make sure GPRS (Mobile Office) is enabled on your phone. This won’t work with Airtel Live :P
2. Install the Bluetooth utilities:
sudo apt-get install bluez-gnome bluez-utils
3. Find the MAC address of your phone:
hcitool scan
The output should be something like this:
Scanning ...
00:19:63:74:XX:YY saurav
Write down this address somewhere for future reference.
4. Now, determine the channel used for dial up networking using the MAC you just found:
sdptool browse 00:19:63:74:XX:YY
...
Service Name: Dial-up Networking
Service RecHandle: 0x10001
Service Class ID List:
"Dialup Networking" (0x1103)
"Generic Networking" (0x1201)
Protocol Descriptor List:
"L2CAP" (0x0100)
"RFCOMM" (0x0003)
Channel: 1
Profile Descriptor List:
"Dialup Networking" (0x1103)
Version: 0x0100
In this case, the required channel is channel no. 1. This will be used to configure the bluetooth connection.
5. Open up /etc/bluetooth/rfcomm.conf with your favorite editor.
sudo nano -w /etc/bluetooth/rfcomm.conf
Make it look something like this (replace with your MAC address and channel):
rfcomm0 {
bind yes;
device 00:19:63:74:XX:YY;
channel 1;
comment "Dial-up Networking";
}
6. Next, restart bluetooth services:
sudo /etc/init.d/bluetooth restart
7. We’re done with the bluetooth configuration. Now we need to configure wvdial:
8. Install wvdial
sudo apt-get install wvdial
9. Run wvdialconf. This generates a dummy /etc/wvdial.conf
sudo wvdialconf
10. Now we need to edit /etc/wvdial.conf and feed in the values for the GPRS connection:
sudo nano -w /etc/wvdial.conf
It should look something like this:
[Dialer Defaults]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
stupid mode = 1
Modem Type = Bluetooth Modem
Baud = 115200
New PPPD = yes
Modem = /dev/rfcomm0
ISDN = 0
Phone = *99#
Username = a
Password = b
11. We’re done. Make sure Bluetooth is turned on in your phone and enter the following command to connect:
sudo wvdial
It might ask you for a PIN the first time you connect, in which case you must enter the same digits in the phone and PC in order to pair them.
12. Press Ctrl-C when you want to disconnect.
